topblog Ivoire blogs

13/10/2017

KTAG 14P600KT06 GPTcable Pinout for DIY users

MED GPT cable 14P600KT06 is necessary to be used with Ktag for Bosch MED17 GPT ECUs reading. So, how to make it your self & how to use it for connection? Here you go.

 

 

What is Ktag 14P600KT06 GPT cable:

It is used for BOSCH MED17 GPT ECUs

How to make a Ktag GPT cable yourself:

 

I take 144300t105 rainbow cable and remake to GPT cable

(or u can use 26 pin connector , may some one will be handful)

for 05 cable:

GPT SIGNALS:

PIN 23 ORANGE

PIN 24 YELLOW

CAN SIGNALS:

PIN 13 ORANGE CAN-H

PIN 14 YELLOW CAN-L

 

the pinout

ktag-GPT-cable-pinout

correct pin out of ori Cable 14P600KT06 GPT:

yellow pin3- yellow

orange pin 4-organge

yellow pin 13-green

orange pin 14-white

ktag-GPT-cable

WARNING: Incorrect or poorly made connections may damage the ECU, often beyond repair. In no event shall we be liable for any damage caused to the ECU by wrong connections. If not equipped with enough knowledge and tech, you’d better spend a bit to buy one and use it with security. Look here: http://www.obdexpress.co.uk/wholesale/V7.020-ktag-ktm-ecu...

ktag-GPT-14P600KT06-cable-pinout

it was tested a lot:

MED 17.7.2 Mercedes GPT 2015

ktag-GPT-14P600KT06-cable-tested

How to connect & use Ktag GPT cable for MED17 GPT ECU reading:

 

  • Plug-in 689: MED17.5.2 IROM TC1767

Ktag-GPT-cable-read-MED17-GPT-1

Ktag-GPT-cable-read-MED17-GPT-2

The pins Boot can be found on the right side of the ECU (in red in the picture).

The programming pads where to set the board adapter are located at the bottom right (in yellow).

Ktag-GPT-cable-read-MED17-GPT-2

Material needed:

 

a.Solder a wire joining the two pins Boot shown in the picture;

b.Solder a wire to pin CNF1 shown in the picture;Ktag-GPT-cable-read-MED17-GPT-4

c.Connect cable 14P600KT02 and cable 14P600KT06 to the ECU connector according to the pinout below:

Ktag-GPT-cable-read-MED17-GPT-5

d.Remove the soldered wires before re-installing the ECU on the vehicle.

09:11 Publié dans Blog | Tags : ktag ecu | Lien permanent | Commentaires (0)

KTAG 14P600KT06 GPTcable Pinout for DIY users

MED GPT cable 14P600KT06 is necessary to be used with Ktag for Bosch MED17 GPT ECUs reading. So, how to make it your self & how to use it for connection? Here you go.

 

 

What is Ktag 14P600KT06 GPT cable:

It is used for BOSCH MED17 GPT ECUs

How to make a Ktag GPT cable yourself:

 

I take 144300t105 rainbow cable and remake to GPT cable

(or u can use 26 pin connector , may some one will be handful)

for 05 cable:

GPT SIGNALS:

PIN 23 ORANGE

PIN 24 YELLOW

CAN SIGNALS:

PIN 13 ORANGE CAN-H

PIN 14 YELLOW CAN-L

 

the pinout

ktag-GPT-cable-pinout

correct pin out of ori Cable 14P600KT06 GPT:

yellow pin3- yellow

orange pin 4-organge

yellow pin 13-green

orange pin 14-white

ktag-GPT-cable

WARNING: Incorrect or poorly made connections may damage the ECU, often beyond repair. In no event shall we be liable for any damage caused to the ECU by wrong connections. If not equipped with enough knowledge and tech, you’d better spend a bit to buy one and use it with security. Look here: http://www.obdexpress.co.uk/wholesale/V7.020-ktag-ktm-ecu...

ktag-GPT-14P600KT06-cable-pinout

it was tested a lot:

MED 17.7.2 Mercedes GPT 2015

ktag-GPT-14P600KT06-cable-tested

How to connect & use Ktag GPT cable for MED17 GPT ECU reading:

 

  • Plug-in 689: MED17.5.2 IROM TC1767

Ktag-GPT-cable-read-MED17-GPT-1

Ktag-GPT-cable-read-MED17-GPT-2

The pins Boot can be found on the right side of the ECU (in red in the picture).

The programming pads where to set the board adapter are located at the bottom right (in yellow).

Ktag-GPT-cable-read-MED17-GPT-2

Material needed:

 

a.Solder a wire joining the two pins Boot shown in the picture;

b.Solder a wire to pin CNF1 shown in the picture;Ktag-GPT-cable-read-MED17-GPT-4

c.Connect cable 14P600KT02 and cable 14P600KT06 to the ECU connector according to the pinout below:

Ktag-GPT-cable-read-MED17-GPT-5

d.Remove the soldered wires before re-installing the ECU on the vehicle.

09:11 Publié dans Blog | Tags : ktag ecu | Lien permanent | Commentaires (0)

06/09/2017

How to online update Xprog 5.5.5 to Xprog Box 5.7.6

This is XPROG 5.5.5 to 5.7.6, software and firmware update internet active

 

  1. Unzip the zip file, run XProgDestop.exe 
    2. Press the Help -> Hardware Info and update the firmware
    3. Do not press the Update Certificate

 

Says it works 100%.

 

But unluckily, i have no luck.

 

I was thinking about upgrading my xprog box so I thought I would have little to lose by following instructions given to see what happens.

Everything appears to go smoothly see pictures below.

However, you cannot read or write any chips without being locked into a certificate error loop. see pics.

Rolling back to 5.5.5 all authorisations are gone hardware registration ID is blank and unit wont read or write.
xprog-5.7.6-update (1) xprog-5.7.6-update (2) xprog-5.7.6-update (3) xprog-5.7.6-update (4) xprog-5.7.6-update (5) xprog-5.7.6-update (6) xprog-5.7.6-update (7)

 

So for the benefit, my advice is don’t use this

 

I finally gave it up and spent some dollars with a new one (Xprog box 5.7.6, it’s from http://www.obdexpress.co.uk/wholesale/x-prog-box-ecu-prog...)

 

It adds new authorization:

 

MCU/MPU->infineon{XC16x}->SAK-XC164CS-16F

MCU/MPU->FresscaleHC08-Updated->MC68HCx08AS/AZ32_CONFIG

MCU/MPU->FresscaleHC08-Updated->MC68HCx08AS/AZ32_CONFIG

MCU/MPU->Fresscale9S08->MC9S08AW8_FLASH

MCU/MPU->Fresscale9S08->MC9S08AW8_FLASH

MCU/MPU->Fresscale9S12XD->MC9S12XDx128_EFPROM

MCU/MPU->Fresscale9S12XD->MC9S12XDx128-EFPROM-secured

MCU/MPU->Fresscale9S12XF->MC9S12XF128_EEE

MCU/MPU->Fresscale9S12XF->MC9S12XF128_EEE

MCU/MPU->Fresscale9S12XHY->MC9S12XHY128_D-FLASH

MCU/MPU->FresscaleMPC55xx->MPC5515_Code-Flash

MCU/MPU->FresscaleMPC560x->MPC5602B/C_Code-Flash

MCU/MPU->FresscaleMPC560x->MPC5602B/C_Code-Flash

Immobilizers->Yamaxa->T-MAX_TYPE_I_9S12T64

Other ECU ->Chrysler-DodgeJeep->BCM-GRAND_CHEROKEE_WK_2014_Flash

Other ECU ->GM ECU->SAF-XC164CS-16F

Other ECU ->HONDA Bikes->CB650F 2015_Code_Flash

Other ECU ->Renault ClioOther ->EPS_ST10F269

Other ECU ->Renault Modus ->ECU_SAK-XC164CS-32F

Airbag(XC2xxx)->FR3T-14B321-AF(XC2336A-72)->FR3T-14B321-AFflash0

Airbag(SPC560xx)/MPC560x)->Honda_CR-V(SPC560P50LS)->Code_Flash

Xprog 5.7.6 has all authorization:

 

AUTH-0001 Motorola HC05 family authorization (allows to read/write EEPROM)

AUTH-0002 Motorola HC08 family authorization (allows to read/write EEPROM)

AUTH-0003 Motorola HC11 family authorization (allows to read/write EEPROM)

AUTH-0004 Motorola HC12, 9S12 family authorization (allows to read/write EEPROM and flash memory)

AUTH-0005 Texas Instruments TMS370/TMS374 family authorization (allows to read/write EEPROM)

AUTH-0006 Motorola HC05Bxx and HC05Xxx family bypass security authorization (allows to read/write secured EEPROM and flash memory)

AUTH-0007 ST M35080 authorization. Read/Write/Erase device to delivery state.

AUTH-0008 BMW EWS3 authorization

AUTH-0009 ATMEGA family authorization (allows to read/write EEPROM and flash memory)

AUTH-0010 MB ZGS001 authorization

AUTH-0011 Motorola HC11EA9/E9 bypass security authorization (allows to bypass security bit and read EEPROM and RAM memory)

AUTH-0012 National CR16 authorization (allows to read/write EEPROM memory)

AUTH-0014 ST7, ST10 family authorization (allows to read/write internal flash)

AUTH-0015 MPC5xx authorization (depending on device program automatically detects MPC5xx, M95xxx device type, flash, external flash and configuration memory size)

AUTH-0018 Motorola HC12, HC912, MC9S12, MC9S12X bypass security authorization (allows to read/write secured EEPROM and flash memory)

AUTH-0020 ARM (Micronas, …) Family authorization (allows to read/write internal flash and external serial EEPROM)

AUTH-0021 ARM (Micronas, …) Family bypass security authorization (allows to read/write secured and non-secured internal flash and external serial EEPROM, view/change mileage, Chassis number (VIN), serial number and PIN code).

AUTH-0023-1 MAC7xxx

AUTH-0023-2 XC23xx

AUTH-0024-1 MC9S12Cxx

AUTH-0024-2 MC9S12XE

AUTH-0024-3 9S12XE SECURITY

AUTH-0024-4 MC9S12HA/HY/P

AUTH-0025-1 MPC/SPC5xxx Authorized 11/4/2014

 

Now, it works perfect:

 

 

xprog-box-5.7.6-1 xprog-box-5.7.6-2 xprog-box-5.7.6-3 xprog-box-5.7.6-4
xprog-5.76-HC912D60-review-1 xprog-5.76-HC912D60-review-1

Src:http://blog.obdexpress.co.uk/2017/09/06/how-to-online-upd...