topblog Ivoire blogs

11/07/2017

Download & Install MaxiLinkII Software

Here is the Autel MaxiTPMS® TS401 TPMS Diagnostic Tool update guide.

1. Download & Install MaxiLinkII Software

The TS401 is updated via the MaxiLinkII software (installed on a Windows PC) and by downloading the Update file from the Maxitpms.com website. The Maxilink II software is available at http://www.maxitpms.com/tpmscms/ product/580.jhtml. From the homepage, www.maxitpms.com, go to Products, then select MaxiTPMS TS401, click on the Downloads tab and then click on Maxi PC Suite TS401 file to download the MaxiLinkII software. To unzip the file, rightmouse click on the file and select Extract All. Double-click on Setup.exe to install.

donwload-autel-ts401-software

2. Download TS401 Update

To download software updates, click here, http://www.maxitpms.com/tpmscms/ product/580.jhtml, then select TS401 Update file. Or from the homepage, www. maxitpms.com, click on Products, then MaxiTPMS TS401, and click the Downloads tab. In the list, click the TS401 Update file to download the zip file. To unzip the file, right-mouse click on the file and select Extract All. Remember to note the location of extracted folder.

Download-TS401-Update

3. Connect Tool to PC

 

Connect tool to the computer using the supplied USB and select Update Mode on the tool.

Note: When an error occurs and the tool is unable to work properly, you may need to update the programs. Power off the tool first and then hold the N button, connect the tool with the computer via USB and then the tool will enter the Update Mode forcedly. Follow the update procedures to refresh the program

autel-ts401-connect-to-pc

4. Update the Tool

IMPORTANT: Both the TS401 file and the DTC file must be updated for the tool to function correctly. There is NO need to register the tool before updating.

Updat-autel-ts401-tool-1 Updat-autel-ts401-tool-2

Launch MaxiLinkII on the PC and then select TS401 on the left-hand side of the screen under the TPMS tab. Under Update Program, click on Select File and browse to the software update you downloaded. Open the folder labelled US, select the file within (the file extension is .bin) and click on Update. The application will communicate with the tool and update. The PC application and the tool will display a message once the update is completed. Next, under Update DTC, click on Select File, browse to file (the file extension is .aut) and click on Open, and then click on Update. The application will communicate with the tool and update its software. The PC application and the tool will display a message once the update is completed. Now your tool is ready to use!

Source:http://www.obdexpress.co.uk/service/autel-maxitpms-ts401-...

www.hobdii.com

02/06/2017

How to install OPCOM VAUX-COM 120309a software on WIN10

This toturial is about  how to step by step install OPCOM diagnostic interface VAUX-COM 120309a software driver on Windows 10, especially for those troubled with “OP-COM usb is not detected on Windows 10”.

Run VAUXCOM.exe

Allow this app to make changes to your device

OPCOM VAUX-COM 120309a software on WIN10 (1)

 

Go to Settings in VAUX-COM 120309a

吧   OPCOM VAUX-COM 120309a software on WIN10 (2)

 

Test interface

test-interface

 

Connect the interface to the USB port, or install the USB driver

install-usb-driver

 

Close VAUX-COM 120309a

Opcom Computer management

Launch the troubleshooter

launch-the-troubleshooter

 

Again, open Computer management

Uninstall USB Serial Converter

Uninstall-USB-Serial-Converter

 

Disconnect the internet

Update driver- OP-COM USB V2

install-driver-op-com

 

Browse my computer for driver software

 

browse-driver-software

 

browse-driver-software 2

 

browse-driver-software 3

 

browse-driver-software 4

 

browse-driver-software 5

 

browse-driver-software 6

 

browse-driver-software 7

 

browse-driver-software 8

 

Continue installing this driver

install-this-driver

 

usb-driver

check-connection

 

Again, run VAUXCOM.exe as administrator

Allow this app to make changes to your device

Go to Settings

Then Test interface

Firmware version tested successfully

firmware-tested

 

Apply settings

apply-setting

Go to Diagnostics

go-to-diagnosis

select-vehicle

select-car-to-test…

Successfully install Op-Com on Windows 10!!

Source:http://obdexpresscouk.blogspot.com/2017/06/how-to-install...

 

 

www.hobdii.com

08:24 Publié dans Blog, software download, Web | Tags : opcom | Lien permanent | Commentaires (0)

01/06/2017

How to setup SDconnect C4 wired connection to PC

This is how to connect SD Connect C4 with Xentry 2014, that failed to registrer my multiplexer and hasn’t LAN connecting into a SD connect.

 

 

 

 

 

Solution... here you go.


You should connect " Wired LAN " MUX to your PC.

Then switch a your PC's icon " wired " .

Changed --> to next ( uploaded configuration movie ) pass : our major pw.

Not changed --> check you wired LAN driver and cable.

Many troubles had SD connect wired LAN module.

If OK your PC and cable

sdconnect_config000:

https://mega.nz/#!bo92ySQB!ajjQoIrVWXS4TmNO5PnDFF31gY7EQF...  If it doesn’t work, try to reinstall " SD net control "

 

Good luck.

 

 

http://blog.mbstartool.com/2017/06/01/how-to-setup-sdconn...