topblog Ivoire blogs

26/05/2017

Vxdiag Multi Diagnostic Tool: Rheingold Techstream IDS 3 in 1

This is VXDIAG Allscanner for BMW TOYOTA FORD/MAZDA.

 

This vxdiag multi diagnostic tool is called VXDIAG A3.

vxdiag-bmw-toyota-ford-mazda

Allscanner vxdiag a3 can be performed as a combination of BMW ICOM A2, Vxdiag vcx nano Ford/Mazda, and Vxdiag vcx nano Toyota.

 

Professionals @obdexpress.co.uk tested its functionality and verified it’s working 100% no issues in OBDII diagnostics, coding, key/ ecu programming.

 

Vxdiag a3 diagnostic tool on BMW works as ICOM A2

wifi-bmw-icom-a2-b-c

Vxdiag A3 and Bmw software worked!

 

ISTA-D 4.04.12………diagnose OK

ISTA-P 3.60.2.001…………….program OK

BMW ETK: 2017.2………read electronic catalogue OK

BMW KSD 09.2016………..read commercial service data OK

BMW Engineer Software:

– INPA………diagnose E series OK

– NCS………..coding E series OK

– WinKFP………..programming E series OK

– E-Sys 3.27.1, Psdzdata 59.0)……..coding f series OK

BMW FSC code generator

BMW AiCoder

 

 

 

Vxdiag a3 on Ford/Mazda works as VCM2 clone or Vxdiag vcx nano for Ford/Mazda

best-ford-vcm-ii-wifi

wifi-version-vxdiag-vcx-nano-for-ford-mazda-ids

Vxdiag A3 with Ford IDS software is good at Ford diagnostics and programming as VCM2 china clone and Vxdiag vcx nano Ford do, incl.

 

  1. Programming & Installation of new ECUs (PCM, ABS, Instrument Cluster, Air Bag, Fuel Pumps, etc.)
  2. Live Data-stream with Recording & Playback Functions for Main ECUs
  3. Read & Clear Diagnostic Trouble Codes (DTCs)
  4. New Software Re-flash for Existing ECUs
  5. Set, Adjust or Remove Speed Governors
  6. Automatic vehicle recognition
  7. All Other Dealer Functions
  8. Guided Fault Finding
  9. Steering Angle Resets
  10. Program New Keys
  11. DPF Regeneration
  12. Brake Bleeding
  13. Injector Coding

 

The important tip: VXDIAG NANO vs VCM II : Which is better?

 

Full chip high quality VCM II (SP177-C1) better!

But be careful programming!

 

 

 

Vxdiag a3 on Toyota works as well as Vxdiag vcx nano for Toyota

vxdiag-vcx-nano-for-toyota

Vxdiag A3 Toyota performs well with Techstream software for Toyota/Lexus diagnostics and customizing setting.

 

Some of the more memorable ones are:

Program and erase my own keyless remotes, FOB’s, Smart Keys, Etc….

Change DRLs on or off

Change light sensor for when headlights come on or go off with AUTO mode

Make it so windows roll down when you hold down unlock on your remote for 2.5 seconds.

Roll up/down windows by turning key in the door lock for 2.5 seconds

Turn on or off seatbelt warning buzzer

Turn beeper on/off for doors locking and unlocking with remote

Change door locks on/off when shifting FROM park

Change door locks on/off when speed over 15mph

Change door locks on/off when shifting INTO park

Change doors locks to unlock all doors 10 seconds after driver door opens.

Change delay for how long headlights stay on after ignition off.

Program your TPMS sensors to your vehicle if you get a new/replace one.

Shows temp inside tires, and actual pressure inside each tire including spare.

Every switch in the car is displayed with it’s current status.

Press the Cruise control Accel stick up and it shows that switch is now on.

Pull the stick and it shows the cancel button is now on.

Push window down button and it shows window down button on.

 

Every imaginable sensor, temp, flow, psi, that’s on the vehicle is displayed to you.

 

….

 

Enjoy!

 

24/05/2017

(Solved) Ford IDS 105 VMware Error: 64 bit operation is not possible

When starting virtual machine, some users have got Ford IDS VMware Workstation Error: 64 bit operation is not possible.

 

This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible.

This host supports Intel VT-x, but Intel VT-x is disabled.

Intel VT-x might be disabled if it has been disabled in the BIOS/firmware settings or the host has not been power-cycled since changing this setting.

(1) Verify that the BIOS/firmware settings enable Intel VT-x and disable ‘trusted execution.’

(2) Power-cycle the host if either of these BIOS/firmware settings have been changed.

(3) Power-cycle the host if you have not done so since installing VMware Workstation.

(4) Update the host’s BIOS/firmware to the latest version.

 

ford-ids-105-64bit-error

That means the cpu isn’t configured / isn’t capable of 64bit virtualization. Check the bios setting

 

To be honest… Just turning nonpersistent off before the first start is all users need to do… And also click i moved it.

Leaving internet on doesn’t matter.

In fact users need to keep it on if users wanna do programming from the server.

So, about the Vmware error on start up:

Just change computer BIOS about virtualization that was disabled, change to enabled. Then IDS is working ok!!!!

ford-ids-105-64bit-solution

 

A good tip from obdexpress.co.uk - How to install Ford IDS 105 on a VMware machine:

> Downloaded & extracted:

Ford IDS V105.01 + VCM II Manager 2.3.85.7: (Pass: nK6gE84)

(In one of the first couple of lines in config file change the “12” to “10”)

> Clicked “I MOVED IT”

> Turned of internet (dunno if it matters).

> Turned off nonpersistent.

> Started Up IDS 105.1 VMWARE

> Plugged in OEM VCM and installed drivers.

> Made cosmetic changes, performance changes to WIN7.

> Opened IDS and made settings changes

> Ran Shut down command in Guest System.

> Turned nonpersistent back on.

I did 6 module programming on a 2013 explorer yesterday and it went flawlessly with VCM2 clone (SP177-C1 it’s a wifi version)..

 

 

(Solved) Ford IDS 105 VMware Error: 64 bit operation is not possible

When starting virtual machine, some users have got Ford IDS VMware Workstation Error: 64 bit operation is not possible.

 

This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible.

This host supports Intel VT-x, but Intel VT-x is disabled.

Intel VT-x might be disabled if it has been disabled in the BIOS/firmware settings or the host has not been power-cycled since changing this setting.

(1) Verify that the BIOS/firmware settings enable Intel VT-x and disable ‘trusted execution.’

(2) Power-cycle the host if either of these BIOS/firmware settings have been changed.

(3) Power-cycle the host if you have not done so since installing VMware Workstation.

(4) Update the host’s BIOS/firmware to the latest version.

 

ford-ids-105-64bit-error

That means the cpu isn’t configured / isn’t capable of 64bit virtualization. Check the bios setting

 

To be honest… Just turning nonpersistent off before the first start is all users need to do… And also click i moved it.

Leaving internet on doesn’t matter.

In fact users need to keep it on if users wanna do programming from the server.

So, about the Vmware error on start up:

Just change computer BIOS about virtualization that was disabled, change to enabled. Then IDS is working ok!!!!

ford-ids-105-64bit-solution

 

A good tip from obdexpress.co.uk - How to install Ford IDS 105 on a VMware machine:

> Downloaded & extracted:

Ford IDS V105.01 + VCM II Manager 2.3.85.7: (Pass: nK6gE84)

(In one of the first couple of lines in config file change the “12” to “10”)

> Clicked “I MOVED IT”

> Turned of internet (dunno if it matters).

> Turned off nonpersistent.

> Started Up IDS 105.1 VMWARE

> Plugged in OEM VCM and installed drivers.

> Made cosmetic changes, performance changes to WIN7.

> Opened IDS and made settings changes

> Ran Shut down command in Guest System.

> Turned nonpersistent back on.

I did 6 module programming on a 2013 explorer yesterday and it went flawlessly with VCM2 clone (SP177-C1 it’s a wifi version)..