topblog Ivoire blogs

30/09/2018

K+DCAN usb for 545 e60 2005 programming and coding results

I can show you my programming and coding results few day before for my 545 e60 2005..with K DCAN usb...

Requirements for installation of ISTA P : min 200 gb free hdd,min 3-4gb RAM,and min 2ghz cpu speed,i hope you know...

I don't know for sure do you need to keep ISTA +,because I have installed Ista + before ISTA P version 3.65.0.500 which I have...

I don't remember thru that installation of ISTA P that I was needed some kind of activation key, only reg fix or something ...but anyway, now I have a new version of ISTA P3.65.0.500 so you can go thru installation of 3.65.0.500 version [85 gb]...[there is ISTA P loader folder with activation key ]

About my experience, I must tell you that with K DCAN usb cable everything was fine but slow...

For my CCC Application programming time was about 8 hours!!!

Everything else was much faster,  think I have 38 ecu programmed and coded thru ISTA P....

I have done full car programming in about 12 hours!!!

Yes I know it is crazy, but when it started, I must to finish everything...

BMW ICOM is much better[and faster] solution!

But for my car it was a problem for old ZSUB numbers which I did not managed to program

all ecu-s thru WinKFP ,one by one..only few of them.

Everything about ecu-s in my bmw was from 2005 [integration level plant E060-04-09-550]

Anyway I think there is no problem for programming 1 ecu with K DCAN usb, but keep in mind that voltage of the battery must be backup all the time and key must be on ignition position ...

And one more thing, for me WinKFP is also good solution for programming, because when you have new ZSUB numbers {ecu numbers} ,you just need to find that number in AIF thru INPA, and after that you just in WInKFP comfort mode [F1] ,put that number [F1],enter VIN [F4],than DONE[F8] and than [F3] again and everything is done!

Or just update ecu with [F3],than select ecu family,enter VIN [F4],than [F8] and again [F3]...

I hope you don't mind for this long thread, and also sorry for my English writing ,because I don't know better...

PS:ISTA P is only for programming and coding ,not for diagnostic....so keep your ISTA +

BMW E60 ISTA /P final report:

https://mega.nz/#!gZwBXIaS!KWoT-7k4zsU21zvBvOXC2Wu95_-heL...

 

www.obd2eshop.com

 

Source:

http://blog.obd2eshop.com/kdcan-usb-for-545-e60-2005-prog...

09:37 Publié dans Blog | Tags : bmw icom | Lien permanent | Commentaires (0)

11/04/2018

How to check BMW ICOM firmware need update + how update it?

BMW ICOM A2 diagnostic interface failed to be connected, because the firmware is too old and need to upgrade it.

 

Firstly, you need to learn how to check BMW ICOM firmware need update.

bmw-icom-a2-firmware-update-02
update the firmware of BMW ICOM Interface. You have no need to update it if it says FREE.
Please read the above photo. It shows FIRMWARE in red frame, that mean you need to

Secondly, update the firmware of BMW ICOM Diagnostic tool step by step.

1.Power on your icom interface by OBD cable, and connect it to computer by LAN cable. PLEASE make sure they are connected well because your interface might be damaged if disconnection during updating.

2.After connected, open the file ENGINEER TOOL on the desktop and you will see a file named ICOM FIRMWARE UPDATE. They are 2 BINs inside of it, ICOM-APPLICATIONIMAGE-XXX and ICOM-BOOTIMAGE-XXX. They are the files

 bmw-icom-a2-firmware-update-03

3.Open your IE and input the IP address of your icom. If you do not know what is the IP of your icom, you can use ISTA-D to find it. As below, the IP in green frame is the IP of your ICOM. It needs ID and password to enter in, the ID is root,pw is NZY11502.

 bmw-icom-a2-firmware-update-05

  1. After entering into ICOM by IE.Click UPDATE FIRMWARE and choose ICOM-BootImage-XXX.bin,choose Image type as SYSTEM and click SEND THE FILE. Click YES when he say Write the image file to the flash? You will see the red right blinks after that.

bmw-icom-a2-firmware-update-04

 

5.Now we click UPDATE FIRMWARE and choose ICOM-ApplicationImage-xxx.bin and then choose the Image type as APPLICATION and then click SEND THE FILE. Click YES when he says Write the image file to the flash?

6.Reboot your ICOM interface after you update those APPLICATIONIMAGE and Bootimage. And you need to wait for few minutes. Go to ISTA-D again, you will see the FRIMWARE turn to FREE. That means your interface is matched to latest BMW ICOM ISTA software.

 bmw-icom-a2-firmware-update-06

Done!

Hope it helps!

Any question, please feel free to contact www.obd2eshop.com, email at: Sales@OBD2eShop.com

 

Thanks for reading!

 

2018.3 BMW ICOM Software HDD ISTA-D 4.09.13 ISTA-P 3.63.2.001 Engineering Mode support Windows 7 $99

 

 

 

http://blog.obd2eshop.com/how-to-check-bmw-icom-firmware-...

09:44 Publié dans Blog | Tags : bmw icom | Lien permanent | Commentaires (0)

How to check BMW ICOM firmware need update + how update it?

BMW ICOM A2 diagnostic interface failed to be connected, because the firmware is too old and need to upgrade it.

 

Firstly, you need to learn how to check BMW ICOM firmware need update.

bmw-icom-a2-firmware-update-02
update the firmware of BMW ICOM Interface. You have no need to update it if it says FREE.
Please read the above photo. It shows FIRMWARE in red frame, that mean you need to

Secondly, update the firmware of BMW ICOM Diagnostic tool step by step.

1.Power on your icom interface by OBD cable, and connect it to computer by LAN cable. PLEASE make sure they are connected well because your interface might be damaged if disconnection during updating.

2.After connected, open the file ENGINEER TOOL on the desktop and you will see a file named ICOM FIRMWARE UPDATE. They are 2 BINs inside of it, ICOM-APPLICATIONIMAGE-XXX and ICOM-BOOTIMAGE-XXX. They are the files

 bmw-icom-a2-firmware-update-03

3.Open your IE and input the IP address of your icom. If you do not know what is the IP of your icom, you can use ISTA-D to find it. As below, the IP in green frame is the IP of your ICOM. It needs ID and password to enter in, the ID is root,pw is NZY11502.

 bmw-icom-a2-firmware-update-05

  1. After entering into ICOM by IE.Click UPDATE FIRMWARE and choose ICOM-BootImage-XXX.bin,choose Image type as SYSTEM and click SEND THE FILE. Click YES when he say Write the image file to the flash? You will see the red right blinks after that.

bmw-icom-a2-firmware-update-04

 

5.Now we click UPDATE FIRMWARE and choose ICOM-ApplicationImage-xxx.bin and then choose the Image type as APPLICATION and then click SEND THE FILE. Click YES when he says Write the image file to the flash?

6.Reboot your ICOM interface after you update those APPLICATIONIMAGE and Bootimage. And you need to wait for few minutes. Go to ISTA-D again, you will see the FRIMWARE turn to FREE. That means your interface is matched to latest BMW ICOM ISTA software.

 bmw-icom-a2-firmware-update-06

Done!

Hope it helps!

Any question, please feel free to contact www.obd2eshop.com, email at: Sales@OBD2eShop.com

 

Thanks for reading!

 

2018.3 BMW ICOM Software HDD ISTA-D 4.09.13 ISTA-P 3.63.2.001 Engineering Mode support Windows 7 $99

 

 

 

http://blog.obd2eshop.com/how-to-check-bmw-icom-firmware-...

09:44 Publié dans Blog | Tags : bmw icom | Lien permanent | Commentaires (0)