topblog Ivoire blogs

29/08/2019

How to Reset BMW Airbag via Carprog Ecu Tunning?

BMW airbag sensor after car crash and airbag deployment can by locked (Control unit faulty) and must be replaced. Even after small accident Airbag sensor will write in internal memory special
error message "crash data stored" or “computer fault” and after you need to exchange very expensive sensor to new one. With carprog Airbag Reset Tool you can reset and repair airbag computer in 1 minute.

reset-bmw-airbag-carprog-1

We are glad to present new device for BMW Airbag repair. You can see some differences between old and new devices bellow:

reset-bmw-airbag-carprog-2

+/- supported units ZAE, MRSZ, MRSZ3, MRSZ4 (not all)
+ supported units BAE, ZAE, ZAE2, MRSZ, MRSZ2, MRSZ3, MRSZ4

 

There are few major types of BMW Airbag ECU's:

1. BAE

reset-bmw-airbag-carprog-3

2. ZAE
No picture
No need to remove from car!
EEPROM read/write, Crash Data clear, Error Memory read/erase.
Pin 9 – K line
Pin 5 - +12V
Pin 6 - GND

 

3. ZAE2
No picture
No need to remove from car!
EEPROM read/write, Crash Data clear, Error Memory read/erase.
Pin 9 – K line
Pin 5 - +12V
Pin 6 - GND

 

4. MRSZ

reset-bmw-airbag-carprog-4

5. MRSZ2

reset-bmw-airbag-carprog-5

6. MRSZ3 – Temic

reset-bmw-airbag-carprog-6

7. MRSZ3 – Bosch

reset-bmw-airbag-carprog-7

8. MRSZ4 – Temic

reset-bmw-airbag-carprog-8

9. MRSZ4 – Bosch

reset-bmw-airbag-carprog-9

Using these pictures you can erase airbag “on the table” – you must connect GND, +12V, and Diagnostic line between airbag sensor and carprog full, connect power supply to GND
and +12V and use Eraser like in the car. After erasing don’t connect power supply again – BMW airbag sensor is very sensitive and can write “controller malfunction” error after connection on the
table without car.

OBDII – BMW 20 pin connection diagram (or you can user any OBDII to BMW converter):

reset-bmw-airbag-carprog-10

reset-bmw-airbag-carprog-11

www.obdiitool.co.uk

12:00 Publié dans Blog | Tags : carprog | Lien permanent | Commentaires (0)

28/08/2019

Free Download Benz C6 VCI DoIP 1.5.3

WiFi Benz C6 VCI diagnostic tool DoIP firmware is possible to be updated by link.

 

DoIP firmware version: 1.5.3

Compatible device: Benz C6 VCI with DoIP function

BENZ-C6-VCI

Free download Xentry VCI DoIP Update Tool 2.2

https://mega.nz/#!fmxWECDR!V0khe_gi4licjekI0nIRohytSQbtCJ...

sp332-firmware-update

How to update Benz C6 DoIP firmware?

1.) Download DoIP update tool 2.2 above

2.) Connect DoIP VCI with laptop (It will give Connect refused error if not connect VCI with laptop)

3) Run update tool and press update.

4) Wait until upgrade success.

 

Note:

C6 VCI comes without software.  Xentry software with keygen is available to purchase here:

http://www.obdiitool.co.uk/wholesale/benz-c6-vci-software...

04:53 Publié dans Blog | Tags : benz c6 vci | Lien permanent | Commentaires (0)

Free Download Benz C6 VCI DoIP 1.5.3

WiFi Benz C6 VCI diagnostic tool DoIP firmware is possible to be updated by link.

 

DoIP firmware version: 1.5.3

Compatible device: Benz C6 VCI with DoIP function

BENZ-C6-VCI

Free download Xentry VCI DoIP Update Tool 2.2

https://mega.nz/#!fmxWECDR!V0khe_gi4licjekI0nIRohytSQbtCJ...

sp332-firmware-update

How to update Benz C6 DoIP firmware?

1.) Download DoIP update tool 2.2 above

2.) Connect DoIP VCI with laptop (It will give Connect refused error if not connect VCI with laptop)

3) Run update tool and press update.

4) Wait until upgrade success.

 

Note:

C6 VCI comes without software.  Xentry software with keygen is available to purchase here:

http://www.obdiitool.co.uk/wholesale/benz-c6-vci-software...

04:53 Publié dans Blog | Tags : benz c6 vci | Lien permanent | Commentaires (0)